HP Migrating &Troubleshooting Enterprise Networks Sample Questions:

1. Click the Exhibit button and view a network diagram and a switch configuration.

The 10 Gigabit Ethernet link 1/0/25 shown in the exhibit is disconnected from HP A5800 switch IRF member 8 for several minutes. What happens several minutes after the cable is reconnected? (Select two.)

A) IRF Member 8 reboots.
B) IRF Member 4 is the Master.
C) IRF Member 4 reboots.
D) More than one switch is Master.
E) IRF Member 8 is the Master.
F) The IRF split stack is not detected.

2. Click the Exhibit button and view a network diagram and two switch configurations.

After you issue the command irf-port-configuration active on HP A5800 Switch members 4 and 5, the 10 Gigabit Ethernet link 1/0/25 is connected. What is the expected result?

A) IRF Member 3 becomes the Master.
B) IRF Member 2 becomes the Master.
C) IRF Member 5 becomes the Master.
D) IRF Member 4 becomes the Master.

3. Click the Exhibit button and view a network diagram and two switch configurations.


Traffic from AS 65006 destined for network 16.1.0.0 /16 enters AS 65001 via the Serial 3 interface of Router 1. The administrator prefers that this traffic enter AS 65001 via interface Serial 6 of Router 1. Which configuration changes on Router 1 are required to achieve the desired result?

A) route-policy PolicyB permit node 10 if-match ip-prefix Prefix1 apply as-path 100 100
B) route-policy PolicyD permit node 10 if-match ip-prefix Prefix1 apply as-path 100 100
C) route-policy PolicyB permit node 10 if-match ip-prefix Prefix1 apply cost 100route-policy PolicyD permit node 10 if-match ip-prefix Prefix1 apply cost 200
D) bgp 65001 peer 16.1.6.1 ebgp-max-hop 2
E) route-policy PolicyB permit node 10 if-match ip-prefix Prefix1 apply cost 200route-policy PolicyD permit node 10 if-match ip-prefix Prefix1 apply cost 100
F) bgp 65001 peer 16.1.6.1 next-hop-local

4. You want to replace a Cisco access switch with an HP edge switch. The Cisco switch is configured with the following commands:

How would you achieve the equivalent result? (Select two.)

A) On an HP ProVision ASIC-based E-Series switch, you should use the authorized-manager command.
B) On an HP ProVision ASIC-based E-Series switch, you should create an access list and apply it on the vty interfaces.
C) On an HP A-Series switch, you should create an access list and apply it on the vty interfaces.
D) On an HP A-Series switch, you should create an access list and apply it to the VLAN interface of the management VLAN.

5. You are connecting an HP A-Series switch to the edge of an existing Cisco LAN that is running RapidPVST+. Cisco distribution switches are the root and secondary root in all VLANs. The long pathcost method is enabled on all Cisco switches, and the cost of the ports between the distribution switches is set to 10000. Gigabit Ethernet uplinks are configured as dot1q trunks and all VLANs are permitted. You enable MSTP on the HP A-Series edge switch.What is the topology and Spanning Tree functionality? (Select two.)

A) The HP A-Series switch receives standard BPDUs in VLAN 1. The uplink connected to the root switch is the root port in the CIST. The other uplink port is blocked in VLAN 1 but forwarding in the other VLANs because the switch does not recognize the PVST+ BPDUs.
B) HP A-Series edge switch receives standard BPDU in VLAN 1. The uplink connected to the root switch is root port, the other uplink port is not blocked.
C) HP A-Series edge switch receives standard BPDU in VLAN 1. The uplink connected to the root switch is root port, the other uplink port is blocked.
D) PVST+ BDPUs are not forwarded by the HP edge switch because one uplink is blocked.
E) PVST+ BDPUs are forwarded by the HP edge switch because both uplinks are up.

Solutions: