HP Delta-Aruba Certified Switching Professional Sample Questions:

1. A network administrator needs to create a backplane stack with four AOS-Switches. The administrator wants to choose which switch becomes the commander. Which procedure meets those needs?

A) Configure backplane switches settings on each switch while disconnected. Make sure the desired commander has priority value 1. Then, connect the switches.
B) Configure backplane switching settings on each switch while disconnected. Make sure the desired commander has member ID 1. Then, connect the switches.
C) Boot up the desired commander first and make sure stacking is enabled on it. Then, connect the stacking links and boot the other switches.
D) Boot all of the switches at the same time and then connect the backplane stacking links. Then, access the desired commander, and make sure it has member ID 1.

2. Refer to the exhibit.

Endpoints in VLAN 2 connect directly to this switch. These devices should only be able to send DHCP, DNS, HTTP, and HTTPS traffic. However, they are able to send any traffic. Based on the exhibit, what is the issue?

A) The name of the ACL applied to VLAN 2 is incorrect.
B) The ACL lacks a deny ip any any statement at the end.
C) The switch does not have an IP address on VLAN 2.
D) The ACL is applied in the wrong direction.

3. Two 5400R AOS-Switches are OSPF neighbors. The network administrator wants routing paths to update as quickly as possible in the event of a failure on a neighboring switch.
Which technology should the administrator implement on the connected switch interfaces?

A) MAC Lockdown
B) Spanning Tree Root Guard
C) Bidirectional Forwarding Detection (BFD)
D) Unidirectional Link Detection (UDLD)

4. Refer to the exhibits.
Exhibit 1

Exhibit 2

The network administrator needs to set up BGP between the two company switches, Switch-1 and Switch-2.
The BGP connection does not establish. Based on the exhibits, what does the administrator need to do to fix the issue?

A) Set the update source for the neighbor to the local loopback interface on each switch.
B) Enable BGP on the interfaces that the switches use to reach each other.
C) Enable the multihop option for the neighbor on each of the switches.
D) Enter the network command for 10.0.0.0/24 in the router BGP mode on each switch.

5. Refer to the exhibits.
Exhibit 1

Exhibit 2
Switch-1(config)# spanning-tree
Switch-1(config)# spanning-tree config-name "exam"
Switch-1(config)# spanning-tree instance 1 vlan 10-19
Switch-1(config)# spanning-tree instance 2 vlan 20-29
Switch-2(config)# spanning-tree
Switch-2(config)# spanning-tree config-name "exam"
Switch-2(config)# spanning-tree instance 1 vlan 10-19
Switch-2(config)# spanning-tree instance 2 vlan 20-29
Switch-2(config)# spanning-tree priority 0
Switch-2(config)# spanning-tree instance 1 priority 0
Switch-2(config)# spanning-tree instance 2 priority 1
Switch-3(config)# spanning-tree
Switch-3(config)# spanning-tree config-name "exam"
Switch-3(config)# spanning-tree instance 1 vlan 10-19
Switch-3(config)# spanning-tree instance 2 vlan 20-29
Switch-3(config)# spanning-tree priority 1
Switch-3(config)# spanning-tree instance 1 priority 1
Switch-3(config)# spanning-tree instance 2 priority 0
Switch-4(config)# spanning-tree
Switch-4(config)# spanning-tree config-name "exam"
Switch-4(config)# spanning-tree instance 1 vlan 10-19
Switch-4(config)# spanning-tree instance 2 vlan 20-29
The network administrator enters the commands shown in Exhibit 2. What is the spanning tree status on A1 and A2?

A) Both A1 and A2 block traffic.
B) A1 blocks traffic, and A2 forwards traffic.
C) A1 forwards traffic, and A2 blocks traffic.
D) Both A1 and A2 forward traffic.

Solutions: